Join CTS for virtual webinars and events
Cincinnati Test Systems is thrilled to offer both live and recorded webinars for our global customer-base.
These free sessions are intended for beginner and intermediate operators and engineers to expand their expertise and knowledge of various important leak testing topics:
- Pressure Decay Technologies
- Mass Flow Technologies
- Trace Gas Technologies (Sniff, Accumulation, Hard Vacuum Mass Spec)
- Bubble Testing Conversion to Volumetric Leak Rate
- IP67, IP68, IP69, and a Coorelation to Test Pressure and Leak Rate
- Test Part Sealing Technology and Successful Techniques
More information about each of our virtual events is listed below. We have covered a variety of topics and new topics will be announced periodically.
Upcoming Events
Effective Leak Testing for Die Castings
March 22, 2022
11 a.m. ET, 10 a.m. CT, 8 a.m. PT
The porosity of die cast components can make leak testing a challenge in manufacturing. Join CTS for a webinar to get insight on how to improve the leak test for greater repeatability, improved quality, and shorter cycle times.
LEARN MORE & REGISTER >
Effective Leak Testing of HVAC/R Components
March 24, 2022
11 a.m. ET, 10 a.m. CT, 8 a.m. PT
Leveraging decades of CTS experience, this session was developed to address the common questions and challenges that manufacturers of heating, ventilation, cooling and refrigeration assemblies have with leak testing.
LEARN MORE & REGISTER >
To view a past session (listed below), please fill out our online registration form (click here)。
Pre-Recorded Webinar Sessions
Session #1: Leak Testing 101 – Introducing the Fundamentals• Correlating Leak Rates
• Variation Related To Leak Testing
• Technology Overview
• Technology Sensitivity
Session #2: Overview of Pressure Decay Leak Testing
• Volume Dependency
•周期影响因素
• Calibration
• Vacuum Decay
• Differential Pressure Decay
Session #3: Overview of Mass Flow Leak and Flow Testing
• Technology Overview
• Factors Affecting Repeatability
• Calibration
• Differential Mass Flow
• Pressure Controlled Regulation
Session #4: Hard Vacuum Mass Spec Leak Testing
• What is Hard Vacuum leak testing
• How does Hard Vacuum leak testing work
• What components make up the Hard Vacuum System
• When should a Hard Vacuum System be used over another technology
Session #5: Conduct Leak Location Testing after a Rejected Leak Test
• TracerMate II
• Trace Gas Sniff Test Techniques
• Trace Gas Background Control
• Re-test
Session #6: Leak Station Optimization
• Sealing Techniques
• Factors Affecting Repeatability
• Hold Back Force
• Seal Wear
Session #7: Effective Sealing Techniques and CTS Connect Seals
• Manual Placement of Seals
• Pneumatic Actuation versus Manual Actuation
• Automated Placement of Seals
• Medical Applications and the Differences from other Industrial Applications
Session #8: How to Set Up a Medical Device Pressure Decay Leak Test
• Key Characteristics of Device
• Initial Timer Settings
• Optimizing Fill Time
• Optimizing Stabilization Time
• Optimizing Test Time
• Optimizing Exhaust Time
Session #9: How to Set Up a Medical Device Mass Flow Leak Test
• Key Characteristics of Device
• Initial Timer Settings
• Optimizing Fill Time
• Optimizing Test Time
• Optimizing Exhaust Time
Session #10: How to Set Up a Medical Device Blockage Test
• Key Characteristics and Reject Criteria
• Backpressure Occlusion Blockage Setup
• Delta P Blockage Setup
• Mass Flow Blockage Setup
• Flow Controlled Backpressure Occlusion Blockage Setup
Session #11: Alternative Medical Device Tests using Pressure Decay and Mass Flow Part 1
• Multi-Port Sequential Tests (single & multi-part)
• Bag & Bladder Tests (restraining plates)
• Pressure Rise/Gain Tests
Session #12: Alternative Medical Device Tests using Pressure Decay and Mass Flow Part 2
• Volumetric Verification Tests
• Sealed Component Tests
Session #13: Alternative Medical Device Tests using Pressure Decay and Mass Flow Part 3
• Burst Tests
• Check Valve Cracking/Opening Tests
• Proof Tests
• Basic instrument integration
• Leak test cycle time estimation
• Instrument control and data collection
• Sealing and fixturing techniques
